欢迎进入东莞市渝升五金机械有限公司网站!
东莞市渝升五金机械有限公司
10年冲床生产经验
冲床稳定、安全、耐用、节能
渝升阿里店铺
服务热线:0769-8671-1655
产品分类
4新闻中心
您的位置:首页  ->  新闻中心

自动冲床操作要求


自动冲床的操作要求

1操作人员首先应了解机器的结构、性能和技术参数;绝对不允许超负荷使用,待压工件的变形力一定要小于机器的公称压力。模具不许偏装,工件不许偏压裁。

2压力机附近要收拾整洁,在机器上不得有散乱的毛坯料和废料、碎屑。压力机附近其周围与工作无关的物体必须收拾干净,并将原材料与半成品摆放整齐。

3、开机前,应检查冲压机有无异常状况,如各机构装置包括离合器、制动器、刹车系统、脚踏板等是否正常,磨擦部分及润滑部分有无磨损现象,油杯灌满润滑油

4检查冲模和配合部分是否符合技术要求。安装冲模并调整后可试压一个工件,检查是否合格,然后再正式工作。

5脱开离合器后才可以开动电机,然后再开动机器。如果按下启动按钮电机不转,应立即按下停止按钮,以防烧毁电机。

6做数次空程试验以检查制动离合器、操纵器各部分有无故障,是否动作可靠。电机达到额定转速再开动压力机。



 

 
点图进入相册
10T自动冲床.适合加工各种小五金产品
      1, the operator should first understand the structure of the machine, performance and technical parameters; absolutely not allowed to overload the use of the deformation of the workpiece to be pressure force must be smaller than the nominal pressure machine. Mold allowed partial loading, the workpiece not allowed to bias cut.
     2, press in the vicinity to pick up clean, the machine may not have scattered rough material and waste, debris. Press around the vicinity of work-related objects to be cleaned and neatly placed in raw materials and semi-finished products.
     3, pre-boot, stamping machines should be checked whether the abnormal conditions, such as the installation of various agencies, including clutch, brakes, brake systems, pedal board is normal, friction and lubrication part of the availability of some wear and tear, oil cup filled with lubricant.
    4, check whether the part of die and co meet the technical requirements. Install and adjust the die pressure test after a piece to check eligibility, and then formal job.
    5, disengaged the clutch can be switched on only after the motor, and then switch on the machine. If you press the start button motor does not turn, should immediately press the stop button, to prevent burning of motors.
    6, do a number of air-way test to check the brake clutch, whether the various parts of the manipulator failures, whether the action reliably. Motor to achieve rated speed and then activate the press.
 
[返回]   
上一篇:无
下一篇:无
扫描二维码
  • 扫一扫进入手机网站
    进入手机网站
    扫一扫关注微信公众号
    关注微信公众号
  • 0769-8671-1655东莞市企石镇东平旧围路口斜对面
    电话:13433005018
    联系人:刘先生
  • 东莞市渝升五金机械有限公司 Copyright © 2019 版权所有 访问量: 技术支持【东莞网站建设】【Bmap】【Gmap】【后台管理】 【百度统计 备案号:粤ICP备11043831号